Disc Golf Target Basket Update

May 26, 2009

I’ve been using my disc golf target for about a week now and I’ve found the weaknesses of it.  I’ve been working on some simple fixes to these problems.

From Disc golf target

The first thing I noticed was that a single ring of chain worked for most puts but a few that should have been caught got through.  The simple fix to this was to add a second ring of chains.  I added six more chains halfway between the center and the outer ring.  Very few discs actually make it through the chains.

The second problem was that discs can roll on their side out of the basket.  It didn’t seem like it should happen too often because the disc had to be on its side rolling at an angle.  The solution to this would be to either add more dowels so the disc cant fit through or to add a second plywood ring onto the dowels.  I found that after I added more chain the problem happened less often.

The third thing I noticed was a few of my dowels were not actually hardwood.   They were some lighter weight wood that looked the same.  When the disc hit these dowels they cracked where the screws went in.  I added some glue and a few zip ties to strengthen them.  The best solution would be to make sure all the dowels are some type of hardwood.

Lastly, the extra part of the u bolts that sticks up can really eat away at your discs.   Cutting the excess bolt off and smoothing it with a file helped a lot.


Disc Golf Target Basket

May 19, 2009

I’ve been playing disc golf occasionally for the last few years and I always thought the target / basket would be something I could make.  I did a little research on the internet thinking I would run across some good plans.  There weren’t any that I liked so I made my own.  My design needed to be semi portable and require no welding.

From Disc golf target

Tools required

  • drill & drill bits
  • string & pencil
  • jig saw

Supplies

  • 3/4″ Ply wood
  • 1 in pipe
  • 12 U bolts
  • chain
  • Large (3″) key ring (can substitute with wire)
  • nuts and bolts
    • 12 nuts, bolts, and washers for attaching the Galv Floor Flanges
    • 24 nuts to fit U bolts (2 extra for each)
  • dowels 3/4″ or 1″
  • 2 – 1″ Galv Floor Flange
  • 1- 1 1/4″ Galv FLR Flange
  • 1- 1 1/4″ Galv nipple

I tried to make my disc golf target fairly close to the ones at my local course which uses the Innova DISCatcher® PRO Disc Golf Target. Most of the dimensions for that target can be found by following the link above.  The only dimension I couldn’t find was the depth of the basket which I measured to be 9 inches

Step 1

Cut 3, 26 inch diameter circles from a sheet of plywood.  Take one of the circles and cut out a 22 inch circle within in.  The resulting ring will be used as the rim of the basket portion of the target so be careful not to cut through it.  The 22 inch circle will be the top portion where the chain is attached.  The easiest way I’ve found to cut the circles is to use a nail, pencil, string and jigsaw.  Tie the pencil and nail together 13 inches appart pound the nail in the center and use it to draw a 26 inch diameter circle.  Cut out the circle with the jigsaw.

Step 2

On the 22 inch circle draw a line from the center every 30 degrees (12 lines)  to determine where the U bolts should go.  drill holes for your u bolts.  Each U bolt will require four nuts.  A nut will go on each side of the plywood.  washers are optional.

Note: The U bolts are are sort of optional although I highly recommend them.  You could stick a bolt through the last link of the chain and bolt it to the plywood.

Step 3

Cut your chain in approximately two foot lengths (for me this was 20 links).  Slip one end of the chain on each u bolt and attach them too the plywood circle.  Place the other end of each chain on a large key ring.  The key ring can be substituted with wire but wire will not hold the circular shape.

step 4

Cut 12, 8 inch long dowels and attach them to one of the 26 inch circles (again every 30 degrees).  Attach the ring to the the dowels as well.  now you should have a basket

step 5

Cut the pipe to 55 inches and thread each end.  Most hardware stores will be able to do this for you when you purchase the pipe.

step 6

Attach the 1″ Galv FLR Flanges to the top and base circles.  Drill a 1″ diameter hole through the center of the basket, screw the 1 1/4″ nipple into the 1 1/4″ Galv FLR Flange and attach it to the basket.

step 7

slide the basket onto the pipe and screw on the top and bottom.  Position the basket where it looks right and drill a hole through the nipple and then through the pipe.

step 8 (optional)
An inner ring of chins can be added to the target for better catching.  You will need 6 extra u bolts and some more chain.  the length of chain for the inner ring should be shorter approximately  16 inches (18 links of my chain).  The Innova targets at my local course have 3 rings of chains. for a total of 24 chains.  The single ring seems to work but occasionally lets the disc through.

please see my update on this disc golf target